Factory-direct pathology storage · Luoyang, Henan, China

Export enquiries: younuosh@foxmail.com +86 139 3881 2326
Interchangeable compact system · GT-IC90

Intelligent Compact Block & Slide Cabinet

A 900 mm bay that takes interchangeable block and slide units, with 1.2 mm steel and a central-drive handwheel.

Mixed block & slide Interchangeable 0.8 mm steel 4-section stacking
Intelligent Compact Block & Slide Cabinet
Intelligent Compact Block & Slide Cabinet · GT-IC90 · Mixed block & slide

This is the heavy-duty end of the range. Each bay measures 900 x 520 x 2,050 mm and holds two interchangeable storage units, so a bay can be all blocks, all slides, or one of each. Units lift out and swap without tools, which lets a department rebalance block and slide capacity as case mix changes.

The body is 1.2 mm steel with a seamless welded frame, and the drive runs centrally to rollers on both sides so a loaded bay stays level as it moves. Block drawers take ABS transfer boxes with ten cells; slide drawers use the same upright rows as our static cabinets. Magnetic seals between bays absorb contact, and each drawer has a fall-arrest device.

Specifications

Intelligent Compact Block & Slide Cabinet · GT-IC90
Bay sizeW 900 x D 520 x H 2,050 mm
Storage units2 interchangeable units per bay (block, slide or mixed)
Cabinet steel1.2 mm body; 1.5 mm columns; 0.8 mm side and shelf panels
FrameSeamless welded construction, no exposed weld seams
DriveCentral drive to rollers on both sides, three-stage reduction
Block drawersABS transfer boxes, 10 cells per box
Slide drawersUpright rows, interchangeable with static cabinets
SafetyDrawer fall-arrest, travel limits, anti-tip buffer
SealingMagnetic seals between bays
ToleranceVertical deviation 2.0 mm per bay; track straightness 1.5 mm

Capacity figures are nominal at standard cassette or slide dimensions. Thicker cassettes, thick coverslips and divider strips reduce the real number by roughly 5 to 10 percent.

Design details

Interchangeable units

Swap a block unit for a slide unit when the archive mix changes, without buying a new bay.

1.2 mm steel body

Heavier gauge than a static cabinet, which matters when bays are moved daily on tracks.

Central drive

Power goes to rollers on both sides, so the bay moves squarely instead of skewing on its track.

Three-stage reduction

A geared handwheel keeps start-up force low even with a fully loaded bay.

ABS transfer boxes

Ten-cell boxes lift out of the drawer and carry a case series to the bench in one movement.

Seamless welded frame

No spot welds to crack or rust at the joints; the body is formed and welded as one frame.

Drawer fall-arrest

Each drawer has a mechanical stop that engages if the drawer travels past its limit.

Magnetic bay seals

Buffers between bays absorb impact and keep dust out of the closed stack.

Typical installations

  • Large hospital pathology archives
  • Biobanks with mixed block and slide collections
  • New-build laboratories planning for 20-year growth
  • Departments replacing several static cabinet walls

Questions about this model

How many blocks or slides does one bay hold?

It depends on the units fitted. A bay holds two units; each block unit carries multiple drawers of ten-cell boxes, and each slide unit uses the same rows as our static cabinets. Tell us the mix and we will calculate capacity.

Does it need a special floor?

Yes. The track must be level within a few millimetres over the run, and the floor must carry the loaded bays. We review your floor plan before manufacture.

Can it be extended later?

Bays can be added to the same track run, provided the track was installed with the extension in mind.

Is it motorised?

The standard drive is a manual handwheel with three-stage reduction. Motorised drive can be discussed for very long runs.

Need a cabinet sized to your archive?

Send your block or slide counts, retention period and room plan. We will return a capacity calculation and a quotation within two working days.